General Information About Wire Rope

Wire Rope

STRAND PATTERNS: They refer to different types of arrangements of wires and their diameters within a strand. Common strand patterns are Filler Wire, Seale, Warrington and combinations thereof.

LAY: Indicates how the wires have been laid to form strands and how the strands have been laid around the core. A right regular lay rope (RRL; the most common) has its strands laid right on the rope, similar to threading a right-hand threaded bolt. Regular means that the direction of the wire lay in the strand is opposite to the direction of the strand lay in the rope. (The wires in regular lay rope appear to be in line with the axis of the rope.)

CAUTION: When combining separate ropes in a single line application always use ropes of the same lay pattern. Different lays can increase rotation at connection points decreasing rope efficiency. 

Right Regular Lay (RRL)
Right Lang Lay (RLL)
Left Regular Lay (LRL)
Left Lang Lay (LLL)

PREFORMING: A manufacturing process wherein the strands and their wires are permanently formed, during fabrication, the helical shape that they will ultimately assume in the finished wire rope. Proper preforming prevents the strand and wire from unlaying during normal use. The vast majority of wire ripe sold today is preformed.

FINISH: Wire rope is either sold as “bright” (or “black”), meaning uncoated, or galvanized for better corrosion resistance. “Drawn Galvanized” wire has the same strength as bright wire, but wire, “galvanized at finished size” is usually 10% lower in strength. Plastic coated wire rope is also available, usually galvanized or stainless steel cable. The most common plastic coverings are vinyl or nylon in either clear or white, although other materials and colors are available. These coating do not add strength to the wire rope itself.

LUBRICATION: During fabrication, wire ropes receive lubrication. The kind and amount depends on the rope’s size, type a use, if known. This in-process treatment will provide the finished wire rope with ample protection for a reasonable time if it is stored under proper conditions. But, when the wire rope is put into service, the initial lubrication will normally be less than needed for the full useful life of the wire rope. Because of this, periodic applications of a suitable wire rope lubricant are necessary.

ORDERING WIRE ROPE: Construction, lay, core, finish and other factors mentioned above impart greatly differing characteristics to different wire ropes. They must be understood and considered when selecting wire rope. There is no perfect wire rope for all applications; usually some less desirable properties are traded off for other, more desirable one. Refer to the Wire Rope Users Manual by the Wire Rope Technical Board for a better understanding of wire rope properties and consult professional help when in doubt.

Lacking a complete description of the wire rope desired, a supplier can make several assumptions:

  1. If direction and type of lay are omitted from the rope description, it is assumed to be right regular lay (RRL).
  2. If finish is omitted, this will be presumed to mean ungalvanized, “bright” finish.
  3. If no mention is made with reference to preforming, preformed wire rope will be supplied.
  4. If a supplier receives an order for 6 x 19 wire rope he may assume this to be a class reference and is, therefore, legally identified in furnishing any construction within this category. 

Rereeling Wire Rope

Correct

Wrong

Wrong

When reeling wire rope from one reel to another it is preferable for the wire rope to travel from top to top, as illustrated. Spooling from bottom to bottom is also acceptale, provided the surface over which the wire rope will travel is clean, smooth and dry, so as not to allow foreign particles to become embedded in the wire rope. Spooling from top to bottom or from bottom to top can put a reverse bend into wire rope and must be avoided. When stringing up a machinery wire rope should be removed from the reel in the same direction a s placed on the drum.

Cutting & Seizing Wire Rope

There are numerous ways to cute wire rope, use only appropriate tools specifically designed to cut wire rope. Safety goggles and work gloves must always be worn. Observe other precautions peculiar to the tools used. Wire rope should be properly seized on both sides of the cut with wire or strand. Seizing wire diameter and the number and length of the seizings will depend on the diameter of the wire rope, and whether or not it is preformed.

Breaking In New Wire Rope

Since wire rope is a machine with many moving parts, it requires careful installation and breaking in procedures for maximum safety and long service life. After proper installation, allow the wire rope to run through a cycle of operation at a very low speed. Keep a close watch on the wire rope, its attachments and any working parts such as sheaves, drum, rollers, etc. to make certain that the wire rope runs freely. If no problems appear at this stage, run the wire rope through several cycles of operation under light load at reduced speed. This procedure allows the component parts of the new rope to make a gradual adjustment to the actual operating conditions.

Wire Rope Efficiency

Wire rope will develop 100% efficiency, that is, break at or above minimum acceptance strength (not less than 2 1/2% below nominal breaking strength ) under controlled laboratory conditions.

Once fittings such as sleeves, clips, sockets, etc. are attached and/or the wire rope passes over a curved surface such as sheaves, pins, etc. its strength is decreased. In the case of wire rope passing over a curved surface this decrease in strength depends on the severity of the bend. In the case wire rope fitting, the decrease in wire rope strength will depend on the type of fittings used. The wire rope efficiency usually ranges for 70% – 100%. For more detailed information consult the strength efficiency of wire rope graph on page ## in the ________ section. Note, that hand spliced wire rope, while not using any fittings, has less efficiency than properly flemished and swaged wire rope. There are other factors, depending on the application of wire rope, that can cause a decrease in nominal wire rope strength. They must be considered when choosing a design factor. Refer to the Wire Rope Users Manual and/or other qualified sources for details. 

Elastic Properties Of Wire Rope

Wire rope is an elastic member; it stretches or elongates under load. This elongation can be permanent or recoverable. The extent of elongation will depend on the wire rope used and the design factor chosen. While it may be acceptable for many wire rope uses to neglect its elastic properties, they are of critical importance for some uses. When in doubt about the importance of wire rope elongation consult professional help. Pre-stretching wire rope will only remove some of the constructional stretch and will not totally eliminate elongation under load.

Winding Wire Rope On Drums

Installation of wire rope on a plain or grooved drum requires a great deal of care. Make certain the wire rope is properly attached to the drum. Keep adequate tension on the wire rope as it is wound onto the drum. Guide each wrap as close to the preceding wrap as possible, or follow the groove in case of a grooved drum. No blanket recommendations can be given concerning direction of winding, desirable drum diameter, fleet angle, etc. Consult the Wire Rope Users Manual for this and other important technical information.

Wire Rope Slings

Refer to ASME standard B30.9 and OSHA standard 1910.184 for design factors and other important information. Other standards and information may apply.